>>Please click here to download the product manual<<

Features:nnu30103In1 Design with IPS Displayu3011: This product ingeniously integrates digital oscilloscope, multimeter, and signal generator functions into one device. 3.2-inch clear-definition IPS display, high sensitivity full view display, channel 2 waveforms can be set to green/ cyan/purple.nu3010Signal Generatoru3011: Built-in waveform signal generator, it can output sinewave, sw, trianglewave, and so on. The voltage amplitude is 2.5V, the frequency is adjustable from 0-2Mhz, and the sw duty cycle is adjustable from 1% to 99%.nu3010High-precise Multimeteru3011: Built-in true RMS multimeter, that supports quick software calibration. With DC/ACvoltage, DC/ACcurrent, resistance, capacitance, diode, and continuity test. When measuring low voltage /resistance/continuity, the oscilloscope and multimeter functions can be used simultaneously (small window in the upper right corner).nu3010Digital Oscilloscope Functionu3011: Dual channel oscilloscope function, with 120MHz bandwidth and 250MSa/s sampling rate. With perfect trigger function (automatic, single, normal). Supports sensitivity and time base adjustment, automatic mode adjustment, 2-channel waveform analysis, cursor measurement, reference waveforms, FFT spectrum, reference waveforms, waveform save and view.nu3010Sensitivity and Time Baseu3011: The oscilloscope will automatically detect the signal and adjusts the ranges. Support manual adjustment of the waveform vertically and horizontally. The vertical sensitivity indicates the voltage in the vertical direction, and it is adjusted by the mV and V buttons to adapt to different voltages. The time base represents the time in the horizontal direction. It is adjusted by the S and NS buttons to accommodate different frequencies. In the stop mode, the user can move the waveform left and right.nu3010Two Automatic Modes Adjustmentu3011: Support one-button automatic and fully-automatic mode, no complicated operation, you can quickly detect and display the waveform. In fully automatic mode, no keystrokes are required, and continuous automation is performed.nu3010High Bandwidth & Sampling Rateu3011: The real-time sampling rate is 250MSa/s, dual-channel mode bandwidth is halved to 60Mhz.nu3010Dual Channelu3011: With dual-channel mode, which can measure and display two signal waveforms at the same time for waveform comparison and analysis.nu3010XY Mode for Cursor Measurementu3011: The XY mode is an imaging formed by combining the waveforms of two channels and is commonly used to display the phase difference or frequency relationship between two signals. Supports X cursor and Y cursor measurement. The horizontal cursor can be used, for example, to measure the interval time between two pulses. The vertical cursor can be used to measure the voltage and the voltage difference at any two locations.nu3010FFT Spectrumu3011: FFT (Fast Fourier Transform) is an algorithm that transforms waveforms in the time domain to the frequency domain, which can be used to analyze the frequency component in waveforms. Linear and logarithmic displays are supported. Note: FFT can only display spectrograms, frequency measurement is not supported.nu3010Reference Waveformu3011: Support for latching reference waveforms, statically displaying the current waveform on the screen, while the dynamic waveforms are continue to update normally. And can be used for reference and comparison between multiple waveforms.nu3010Waveform Save/Viewu3011: Save the screen waveform with one click, enter the picture browsing page, you can click the thumbnail for full-screen observation and also can delete the unwanted waveform chart at will.nu3010Safer Designu3011: Use an isolation transformer and isolation optocoupler chip to isolate the multimeter from the oscilloscope, so you don"t have to worry about common ground wiring. (When measuring high voltage, the multimeter, and oscilloscope cannot be used at the same time).nu3010Wide Applicationsu3011: It can easily handle measurement in various fields, widely used in the fields of testing and debugging of electronic circuits, troubleshooting and repairing of electnn nnSpecifications:

nName: 3in1 Digital OscilloscopenMaterial: ABSnDisplay: 3.2 inches IPS color screennBattery: 1 * built-in 2500mah rechargeable lithium battery (included)nCharging: TYPE-C 5VnLanguage: Chinese/Englishnn nnOscilloscope:nnReal-time sample rate: 200MspsnAnalog Bandwidth: 120MHz (CH1 only); 60MHz (CH1+CH2)nEquivalent sampling: 500MnRise time: <3nsnStorage: 128KbnImpedance: 1u039cu03a9nTime Base: 5ns- 10snPeakvoltage: u00b140V (1x), u00b1400V (10x)nTrigger mode: auto/normal/singlenTrigger type: rise/fallnDisplay mode: YT /XY/rollnPersistence: none/1s/u221enAuto mode: oneKey-auto/fully-autonSensitivity: X1:10mV/div~10V/div; X10:100mV/div~100V/divnMeasure items: 14 typesnDC shift: u00b12%nXY mode: yesnScreenshot: yesnFrequency: u00b10.01%nZoom mode: yesnFFT: yesnGenerator waves: sin/square/triangularnGenerator Vol: 2.5Vu00b10.05nGenerator freq: 1Hz-2MHznn nnMultimeter:nDC voltage: 600mV/6.00V/60.0V/600V/750V, u00b1(0.5%+3)nAC voltage: 600mV/6.00V/60.0V/600V, u00b1(1%+3)nDC current: 600mA/10A, u00b1(2%+5)nAC current: 600mA/10A, u00b1(3%+5)nCurrent note: 600mA hole with 1A fuse, 10A hole without fusenResistance: 600.0u03a9u00b1(1.5%+3); 6.000ku03a9/60.00ku03a9/600.0ku03a9u00b1(1%+3); 6.000u039cu03a9, u00b1(1.5%+5); 60.00u039cu03a9, u00b1(3%+3)nCapacitance: 60.00nF/600.0nF/6.000u03bcFu00b1(5%+5), 60.00u03bcF/600.0u03bcFu00b1(10%+5)nDiode: 0.0V~3.3V, 3.3V higher display OLnContinuity: Sound at 50u03a9 and belownnnOther specifications:nItem size: 145 * 86 * 32mm / 5.71 * 3.39 * 1.26innPackage size: 220 * 150 * 70mm / 8.66 * 5.91 * 2.76innPackage weight: 600g / 1.32lbnn nnPackage included:n1 x 3in1 Digital Oscilloscopen1 x Pair of Test Penn2 x Cablen1 x Charging Cablen1 x Set of Accessorynnnn